A Frequent Garage Door Fault with Several Underlying Reasons
A Common Garage Door Problem That Has Several Causes
If your garage door starts to lift and then suddenly comes back down, you are dealing with one of the issues garage door technicians get called about most often. It can seem like the door has a mind of its own, but there is almost always a real reason behind it. Modern garage doors are built with several safety features that stop the door whenever something seems off. A door that reverses on its own is simply one of those safety features doing exactly what it was designed to do. The encouraging part is that most of the reasons behind this behavior are simple to track down and repair. The frustrating part is that more than one thing can trigger the same symptom, so you have to rule them out one by one. The steps below follow the same checking order a trained garage door repair technician would use, which means you may be able to skip a service call if the answer turns out to be an easy one.
The First Thing to Check Is the Photo Eye Sensors
The very first place to look is at the photo eye sensors. You will find them as two small dark boxes attached to the bottom of each side of the garage door opening, just a few inches off the ground. One box shoots an invisible beam across the doorway to the other box. Anytime something interrupts that beam while the door is closing or opening, the door automatically backs up so it doesn't squash whatever it has detected. Step over to the door and take a careful look at both units. They need to be aimed straight at each other with no tilt. Almost every sensor has a tiny indicator light, usually green or red. A green light typically tells you everything is fine. A red light usually points to a blockage or an alignment issue. Inspect the lens for spider webs, dirt, fallen leaves, or any small object resting in front of it. Use a clean, soft cloth to wipe each lens. If the red light stays on after cleaning, carefully tap one sensor a little at a time until both lights show green. Fixing the photo eyes takes care of close to half of the cases where a garage door reverses on its own.
Inspect for Obstructions in the Garage Door Tracks.
If the sensors appear to be functioning properly, the next thing to inspect is the door’s tracks on each side—those metal rails that guide the rollers up and down. Frequently, a tiny object can become lodged in the track, such as a stone, a child’s toy, or a piece of cardboard from a shipped package. When the door lifts, it strikes the obstruction, and the opener interprets the resulting resistance as an unexpected obstacle, prompting the safety mechanism to reverse the door’s motion. Examine both tracks from top to bottom while the door is fully open and clear away any debris. While you’re at it, look for rollers that may be bent or broken, since damaged rollers can also generate resistance that the opener detects as a problem.
Examine the Door's Springs
Just above the door opening, you should see one or maybe two thick metal coils stretched across a horizontal bar. These are known as torsion springs, and they actually carry most of the weight when the door rises. The opener motor is doing far less work than people assume. Its main job is steering the door. The springs handle the heavy lifting. Once a spring wears down with age or snaps completely, the door turns into a very heavy load that the motor wasn't built to lift on its own. After climbing only a small distance, the opener exhausts its strength and sends the door back down. To inspect the springs, look closely at each coil for a noticeable break or split in the wire. When a torsion spring snaps, it usually leaves behind a visible gap of about two inches right where the steel parted. If you do find a broken spring, never attempt the repair yourself. Torsion springs are wound under enormous tension and can release that energy violently, leading to serious harm. Replacing them is work for an experienced garage door professional. Expect the cost of the job to fall somewhere between two hundred and four hundred dollars.
Test the Door's Balance by Hand
Springs can appear normal to the eye while quietly losing the strength they once had. To find out whether yours have weakened, run this quick test. Locate the red emergency release handle that hangs down from the rail beneath the opener, and give it a firm pull. Pulling that handle disengages the door from the motor so it can be operated by hand. Next, lift the door yourself using just your arms. A door with good springs and proper balance will feel almost weightless. A single hand should be enough to raise it, and once you release it around the midpoint, the door should remain in place without sliding. If the door feels noticeably heavy as you lift, or if it slowly drops back down after you let go, then the springs have begun to lose their lifting capacity. This kind of spring weakness sits behind a large share of reported cases where doors reverse before reaching the top. Once your test is complete, push or pull the release handle in the opposite direction to reconnect the door to the opener.
Check the Garage Door Opener's Force Settings
Every garage door opener has two small dials or buttons on the back of the motor housing. One controls the force used to open the door, and one controls the force used to close it. Over time, as parts wear and seasons change, the opener may need slightly more force to do its job. If the force setting is too low, the opener thinks any resistance means it has hit something, so it reverses. The owner's manual for your LiftMaster, Chamberlain, Genie, or Craftsman opener will show you exactly where these settings are. Adjust the open force dial slightly upward, then test the door. Adjust in small steps. Setting the force too high creates a safety risk because the opener will keep pushing even when it shouldn't.
Look at the Travel Limit Settings
The opener's travel limits determine the upper and lower points the door should reach. Incorrectly set limits the opener to mistakenly door has reached its reverse its direction. This issue outage, installation of a new opener, garage door service or maintenance work on the door. Similar to settings, the controls for adjusting the travel limits are located on the back opener motor. Referring to the manual them a simple task. If the door now travels too high or too low, it indicates a problem with the travel limits that should, even if the door is not completely reversing.
Cold Weather Can Cause the Same Problem
In winter, a stiff and cold garage door can put extra strain on the opener. Old grease in the tracks becomes thick, rollers don't spin as smoothly, and the door becomes harder to lift. The opener works harder, hits its force limit, and reverses. If your door only reverses on cold mornings and works fine the rest of the day, this is probably what's happening. The fix is to clean the tracks and lubricate the rollers, copyrights, and springs with a garage door specific lubricant. Avoid WD-40, which actually cleans grease off rather than adding it. Use a lithium or silicone spray made for garage doors.
When to Stop Trying and Call a Pro
If you've checked the sensors, the tracks, the springs, the force settings, the travel limits, and lubricated the door, and it still reverses, it's time to call a garage door repair contractor. At that point, the problem is usually inside the opener itself — a worn drive gear, a failing capacitor, or a damaged logic board. These repairs need proper tools and parts. A good technician can diagnose and fix most issues in under an hour, and the visit usually costs between one hundred and two hundred dollars before parts.